Tutorial 4 iPhone Conversion Kit

If it was easy to disassemble the iPhone 3, it is quite different for the iPhone 4, many of you to ask us for detail, so that's a tutorial to help you change the color of your iPhone 4.

What you'll need to change:

    Special screwdriver iPhone 4 (on sale in the shop)
    Plastic spatula (for mobile phone or any other spatula)

ATTENTION: the dismantling of your iPhone 4 results obviously the immediate suspension of the warranty of your phone. (We can not be held responsible for any damage your iPhone).

1) Removing the Sim Card Tray

Before any operation in your iPhone, make sure to remove your SIM card drawer, you help the extractor on your iPhone.

Removing the iPhone SIM tray 4

Naturally deposited the tray completely

complete removal of the drawer 4 sim iphone

Once filed this one, we can start opening your iPhone 4.

2) Remove the screws under the screen of the iPhone 4

Opening your iPhone 4, passes through this step, unscrew the 2 screws on the iPhone, with the help of a screwdriver (Special iPhone 4).

Removing the two screws on the iPhone 4

3) Removing the back cover of the iPhone 4

Once you remove these two screws, be sure to take the iPhone in vibrate mode, allowing you to remove the hull.

Passage of the iPhone in vibrate mode 4

Once your iPhone 4 in vibrate mode, turn the. Put the shell facing you, and make an upward pressure to slide the back cover up and allow deboitage of the hull.

Deboitage the casing of the iPhone 4

Once you have dislocated the hull, make the switch slowly upward, nothing connected to the hull, but proceed with caution.

deposited in the casing of the iPhone 4

You can complete the trademark (if you decide to change only the back cover by one of our replacement accessories, then place the new shell, and follow the tutorial backwards from this point. For those who carry out a conversion kit, continue).

4) Removing the battery of the iPhone 4

Unlike the iPhone 2 or iPhone 3, or you had to completely disassemble the phone to change the battery on the iPhone 4, the battery is easily accessible. Any disassembly of the iPhone 4, involves removing the battery. Before removing the battery, remove a small piece remains.

Removing the screws iphone battery support 4

Once the screw is removed, you remove the support bracket, help you for this, a plastic spatula or a flat screwdriver.

deposited in the leg maintains battery iphone 4

Complete removal of the leg maintains

Now that the leg maintains is completely removed, you will have access to the outlet, will be disconnected there! using a flat screwdriver or plastic spatula.

disconnection of the battery of the iPhone 4

Now that the iPhone battery is disconnected, you can pull the tab, which will help you remove the battery from the slot.

Removing the battery from the iPhone 4

Battery complement trademark of the iphone 4

5) Removing the vibrating iPhone 4

Maintained by two screws, you will find the vibrator in the upper right corner of the iPhone.

Removing the screw of the vibrator 4 iphone

You can now remove the vibrator.

shaker filed the iphone 4

IPhone Vibrate 4 filed

6) Removing the Upper Cache

This cache maintains and protects the connections at the top of the phone, held by five screws, it will remove the 5 screws, making sure each screw is different, you help our color codes for you there when reassembling.

Removing the cover screws to maintain

Removal of the cache is by the side opposite the camera module.

Removing the cache maintains

This one is clipped onto the chassis of the iPhone, so why not make a bit!

Cache iPhone 4 filed

7) Removing the Camera Module for iPhone 4

Tricky part, the module is directly connected to the motherboard of the phone, disconnected it with a plastic spatula.

Disconnecting the camera of the iPhone 4

Now that you have disconnected it, only module is fitted into the iPhone.

Removing the iPhone camera module 4

Left camera module

7) Removing the motherboard

Above all it will disconnect all modules.

8) Disconnect the module DOCK

Taking dock that connects the module is maintained by a plaque in the middle of the motherboard. Remove the plate by unscrewing the two screws (different screws, the screws do not mix).

Removing the two screws on the motherboard

Now place the plate

Removing the motherboard plate

Plaque motherboard trademark

Once deposited the plate you will have access to decision of the dock, disconnect this one by helping you in the plastic spatula.

Disconnecting iPhone dock taking 4

take off the cloth of the speaker and fold the sheet to access the lower screw on the motherboard and the taking of the speaker.

Folding the sheet of the iPhone 4

8) Disconnect the antenna

Connected to the motherboard through an outlet at the bottom of the antenna.

IPhone antenna connector 4

Disconnect the antenna, with the help of a plastic spatula or a flat screwdriver.

Disconnect the antenna of the iphone 4

Slightly bend the antenna, so as not to damage it when removing the motherboard.

Folding the antenna cable of the iphone 4

9) Disconnect taken by the High

All modules from the top are connected to the motherboard here.

identification taken:

Id catch four modules iphone

    1 - Front camera
    2 - Module Jack, Vibrate button and Volume
    3 - Power button and proximity sensors
    4 - LCD
    5 - Touch

Start all disconnect, starting with the number 1.

Disconnecting taken from the top

Taking disconnected

10) Removing the motherboard

Remove the 2 screws maintains, that you can remove the card.

4 screws motherboard iPhone

Raise a white patch which hides one of two screws.

This is the chip that indicates whether you have opened your iPhone, and turn red when taking moisture.

Removing the iPhone Pastil of 4

Unscrew the last screw, the motherboard is now disconnected from the telephone, you help the spatula to lift the motherboard

Removing the motherboard from the iphone 4

Once raised, completely remove the phone.

Removing the motherboard

11) Removing the Headphone Internal

Top milieur to the internal ear is easily recognizable by its winding copper apparent.Ecouteur internal iphone 4

Stuck on the ground, lift it with the spatula.

takeoff of the internal headphone 4 iphone

Iphone internal earpiece of the four left

Behind him, there is a small plate with a behind the-ear mousseMousse the iphone 4

Remove the foam with the screwdriver.

the foam earpiece lodged

12) Removing the Camera Before

Held by a clip, help you a flat screwdriver to remove it.

Removing the front camera clips iphone 4

Unclip and remove completely.

Clips completely removed

Now get out the camera and help you in the water right.

layer of the camera of iphone 4

Gently pull the tablecloth to the camera déboiter

Removing the camera of the iphone 4

Once dislocated, completely remove the camera.

13) Removing the Screen

Set by nine screws, disassembly. In addition to being screwed, the screen is bonded to the chassis. Press the "staples" with a screwdriver to start off the chassis.

Removing the screws from the chassis 4 iphone

Takeoff of the chassis 4 iphone

Now go a screwdriver gently around the metal frame of the iphone.

Removing the glass from the iphone 4

Then go around the phone completely off the glass + LCD.

CAUTION: The LCD is right on the phone. Do not go too far with the screwdriver during take-off on the tour.

Takeoff of the round window 4 iphone

Once the glass completely detached, take hold of two parts and spread them apart. Pull straight up to avoid damaging the staples of the chassis.

ATTENTION: Pay close pass made in the hole of the front frame to fully open the phone.

deposited in the screen of the iphone 4

Once past the tablecloths, place the glass full frame + LCD.

Screen 4 Iphone completely deposited

Now take the color kit and proceed in reverse, by carefully following all the steps.